Skip to content
| ZGSM
  • Home
  • About usExpand
    • Company Profile
    • Warranty term
    • Blogs
    • News
    • Privacy Policy
  • ProductsExpand
    • LED Street Light

      High Mast Light

      Led Flood Light

      Solar Flood Light

      LED High Bay Light

      tunnel lights

      LED Tunnel Light

      LED Garden Light

      Led Bollard Light

      Solar Street Light

      red green yellow LED Traffic Light

      LED Traffic Light

      LED Canopy Light

      adapter

      Lighting Accessories

  • SolutionExpand
    • Smart Systems

      Smart Systems

      Simulation Design

      Smart Financing

      Smart Financing

  • Applications
  • Case Studies
  • Videos
  • Contact
  • ENExpand
    • FR
    • ES
    • RU
| ZGSM

How to Choose LED Traffic Signals?
A Complete Selection Guide for 2026 (Intersections / Highways / Pedestrian Crossings)

How to Choose LED Traffic Signals? A Complete Selection Guide for 2026 (Intersections / Highways / Pedestrian Crossings)

table of Contents
  1. Introduction
  2. How do LED traffic signals work?
  3. How should LED traffic signals be selected for intersections?
    1. Determine luminaire dimensions based on road classification
    2. Full ball traffic signals or arrow traffic signals?
  4. How should LED traffic signals be selected for expressways and highways?
    1. Mainlines and Tunnels: Lane Control Signals
    2. Ramp Control: Ramp Traffic Signals
    3. Construction Zones, Rural Intersections, and Off-Grid Locations: Solar-Powered LED Traffic Signals
    4. Fog-Prone Areas, Curves, and Accident-Prone Sections
  5. How should LED traffic signals be selected for pedestrian crossings and school zones?
  6. Summary
  7. Related Products
  8. Related Blogs
  9. Related Cases
  10. People also ask
  11. Author introduction

Introduction

When selecting LED traffic signals, the type of unit must be matched to the intersection’s geometry, the control mode, and local regulatory standards—it is not merely a matter of choosing between 200mm, 300mm, or 400mm lens diameters. A comprehensive configuration encompasses various signal types—such as circular (ball) signals, arrow signals, countdown timers, and pedestrian signals—along with the traffic signal controllers that operate them(Learn more about LED traffic signal products ). In essence, selecting LED traffic signals requires answering three questions: Where will they be installed? Who are they intended for? And what system will control them? The table below is provided to assist with quick selection:

Scenario Recommended Luminaire Size (mm) Arrow Light Equipped Countdown Timer Equipped Power Supply Recommendation
Urban arterial road intersections LED full-ball signal lights + directional signal lights Φ400 Recommended (for left-turn protected phases) Recommended (communication type) Mains power + UPS
Secondary/branch road intersections LED full-ball signal lights Φ300 Determined by traffic volume Optional (learning type) Mains power
Expressway mainlines / tunnels Lane control lights (red cross, green arrow) Φ300-Φ400 N/A N/A Mains power + centralized power supply
Expressway ramps / construction zones / off-grid areas Solar yellow flashing lights, mobile signal lights Φ300 /Φ400 N/A N/A Solar power + battery
Crosswalks / schools / hospital exits LED pedestrian signal lights Φ300 N/A Strongly recommended Mains power or solar power

How do LED traffic signals work?

An LED traffic signals system consists of four components: a sensing layer (vehicle detectors), a decision-making layer (traffic signal controllers), an execution layer (LED signal units), and a communication layer (central platform). Detectors collect traffic flow data, while the controller calculates the timing for phase transitions based on a pre-established signal plan (What’s phasing and different signal phase operation?). Through control circuitry—following either a preset sequence or real-time traffic flow data—the system supplies power to the red, yellow, and green LED arrays, causing the corresponding lights to illuminate or flash. This provides visual instructions to manage traffic: red for "stop," green for "go," and yellow as a cautionary transition signal.

How should LED traffic signals be selected for intersections?

The selection process for intersections follows four key rules: use 400mm-diameter signals for main roads and 300mm-diameter signals for secondary roads; include arrow signals where there is a protected left-turn phase; equip new intersections with communication-enabled countdown timers; and always install pedestrian signals at crossings. The specific number of signal units is determined by the number of approach lanes and the signal phasing scheme—more is not necessarily better.

Determine luminaire dimensions based on road classification

Road Class Recommended Size (mm) Recommendation Rationale
Expressways / Arterial roads Φ300 /Φ400 High driving speeds and long viewing distances require a larger luminous surface.
Secondary roads / Branch roads Φ300 Short viewing distance; Φ300 meets requirements and reduces load-bearing on the pole.
Narrow roads / Residential areas Φ200 Space-constrained scenarios; Φ200 size is permitted internationally.

luminous intensity requirements specified in the Chinese National Standard (GB) also vary with the lamp size: for Φ300 and Φ400 non-patterned signal lamps, the luminous intensity on the reference axis (Imin) shall be ≥ 400 cd; whereas for the Φ200 specification, Imin ≥ 200 cd. Additionally, for LED light sources, the maximum luminous intensity (Imax) shall be ≤ 1000 cd (applicable to Φ300/Φ400). This upper limit is imposed to prevent glare caused by excessive brightness (How to reduce glare? ).

Full ball traffic signals or arrow traffic signals?

Scenario Recommended Signal Type
Single incoming lane, all traffic flows released in the same phase Full-ball signal light
Dedicated left-turn phase (protected left-turn) Full-ball signal light + left-turn arrow light
Multi-lane entry/exit, severe conflict between through and left-turning traffic flows Full-ball signal light + left-turn arrow light
Right-turning traffic flow conflicts with pedestrian crossing Add right-turn arrow light
Low traffic volume, no dedicated left-turn phase Full-ball signal light only

Typical LED traffic signals configurations at intersections: At the approaches of major intersections, signals are commonly arranged as "three-aspect vertical" units (red-yellow-green) or "four-aspect" units (red-yellow-green plus a left-turn arrow). When both left-turn and straight-ahead movements need to be indicated, a "circular signal + arrow" combination (with the arrow positioned above the circular signal) or an all-arrow configuration may be used. Depending on specific installation conditions, the signals can be mounted either vertically or horizontally.

Typical LED traffic signals configurations at intersections
Typical LED traffic signals configurations at intersections

How should LED traffic signals be selected for expressways and highways?

On the main lines of expressways, conventional three-color LED traffic signals are generally not used. Instead, lane control signals (red "X" / green "↓") are employed for lane management; solar-powered flashing yellow warning lights and LED guidance systems are used for alerts and delineating the roadway; and mobile traffic signals are utilized for temporary traffic control in construction zones.

LED traffic signals for expressways and highways
LED traffic signals for expressways and highways

Mainlines and Tunnels: Lane Control Signals

Lane control signals are mounted on gantries directly above each traffic lane. They display either a red "×" (lane closed) or a green "↓" (lane open); some versions also include a diagonal yellow arrow, indicating that the lane ahead is closed and prompting drivers to change lanes. The signals should have a diameter of 300mm–400mm and be equipped with visors and anti-glare features. In the dark environment of a tunnel, excessively bright lights can cause severe glare. An ingress protection (IP) rating of IP65 or higher is recommended, given the high humidity, dust, corrosive exhaust fumes, and frequent cleaning requirements found in tunnels. The system must support remote, individual-unit control and status feedback, allowing operators at the control center to toggle lane status—open or closed—with a single click and receive confirmation that the command has been executed.

Ramp Control: Ramp Traffic Signals

Red and green LED traffic signals are installed at the entrance ramps of expressways or highways to regulate the flow of vehicles entering the mainline, thereby preventing congestion. These units typically consist of two aspects (red/green) with a smaller face size and are integrated with vehicle detectors to enable demand-responsive (actuated) control.

Construction Zones, Rural Intersections, and Off-Grid Locations: Solar-Powered LED Traffic Signals

The configuration logic for solar-powered signal lights differs from that of grid-powered units; the primary focus is on energy balance rather than light intensity. When selecting such products, pay close attention to the specifications and lifespan of the solar panels and batteries. The system should have sufficient capacity to operate for at least 7 consecutive days of overcast or rainy weather on a full charge. Additionally, the ingress protection (IP) rating and operating temperature range should be chosen based on the specific deployment environment.

Fog-Prone Areas, Curves, and Accident-Prone Sections

For these locations, rather than standard LED traffic signals, warning and guidance facilities should be used. These include solar-powered yellow flashing warning lights (alternating between a solid yellow display and a red "SLOW" indicator), synchronized solar-powered yellow flashing lights (which create a rhythmic pattern that is more effective at capturing driver attention than isolated flashing lights), delineators, and LED guidance markers.

How should LED traffic signals be selected for pedestrian crossings and school zones?

Estrian crossings shall be equipped with pedestrian signal lights, with priority given to the following configuration: dynamic green walking pedestrian symbol + two-digit countdown timer + voice prompt post for blind pedestrians. For locations such as schools, hospitals, and commercial districts, it is recommended to additionally install pedestrian actuated push buttons (upon activation, the signal controller inserts a pedestrian phase in the next cycle), thereby preventing the pedestrian phase from occupying cycle time when no pedestrians are present. Currently, the common market practice is an integrated signal head combining red standing person and green walking person symbols with a two-digit countdown timer (displaying red and green dual-color digits), where a single lamp head conveys information to both pedestrians and drivers simultaneously.

LED traffic signals for pedestrian crossings and school zones
LED traffic signals for pedestrian crossings and school zones

If the traffic volume does not meet the threshold for installing traffic signals, an alternative pedestrian crossing warning system may be adopted: yellow flashing warning lights + solar-powered flashing road studs + yield signs, supplemented by nighttime illumination. Such solutions are low-cost and quick to deploy; however, it should be noted that they serve merely as warnings and do not replace the right-of-way allocation function of LED traffic signals.

Summary

This article provides recommendations for selecting LED traffic signals based on various application scenarios and offers a brief overview of how do LED traffic signals work. We hope this information assists you in your selection process. Please feel free to contact us for further product details or technical support.

Related Products

pedestrian signal heads

Pedestrian Traffic Light

Arrow traffic light-7

300mm (12’’) Traffic Arrow Lights

traffic light

300mm (12’’) Traffic Signals Lights

Arrow traffic light-10

Lane Control Lights

Arrow traffic light-4

200mm (8’’) Arrow Traffic Light

Related Blogs

Traffic signals

Traffic signals and how do they work

TagsTraffic signals
IP rating

IP rating-important factor of LED lights

TagsIP rating

Related Cases

Arrow traffic light

200mm Arrow traffic light in Colombia

Street traffic light

Street Traffic Light and Crosswalk Light in Ecuador

Crossing light and road traffic light in Dominica

300mm Traffic Lighting System in Peru

200mm LED Crossing Light in Colombia

People also ask

  1. Focusing solely on brightness while ignoring light intensity distribution. The national standard provides specific tables for how light intensity should be distributed across various angles; a signal that is bright at the center but dims rapidly toward the edges will appear significantly darker when viewed from an angled lane.
  2. Overlooking visors (sunshades). Without a compliant visor, sunlight hitting the face of the signal at midday can cause a "false display"—a direct safety hazard. Always confirm that the visor is included as standard equipment.
  3. Selecting the wrong operating mode for countdown timers. Installing a "learning-type" (self-adaptive) countdown timer at an intersection with adaptive traffic control will cause the display to go blank for several cycles every time the control scheme switches. Always determine the type of traffic controller in use before selecting a countdown timer.
  4. Using standard urban intersection traffic lights for freeway lane control is inappropriate. Freeways require dedicated lane-control signals (e.g., a red "X" or a green "↓"), not the three-color circular signal heads used at city intersections.
  5. Focusing solely on the signal heads while ignoring the integration between the traffic controller and vehicle detectors is a mistake. The signal heads are merely the final output devices; the effectiveness of actuated control, adaptive control, or "green wave" (coordinated) traffic flow depends on the traffic controller and the detectors, not on the signal heads themselves.

Signals with a diameter of 400mm (Φ400) are used for urban arterial roads and expressways; 300mm (Φ300) signals are used for secondary arterial roads and branch roads; and 200mm (Φ200) signals may be used for center-mounted poles in space-constrained areas or on roads within residential complexes. The selection is based on vehicle speed and viewing distance—higher speeds and longer viewing distances require larger illuminated surfaces.

The most common reason is the use of a "learning-type" countdown timer. These units require one cycle to "learn" the timing and another to "verify" it, meaning they only begin to display correctly from the third cycle onward. Furthermore, they must re-learn the timing whenever the signal plan changes (e.g., transitioning from peak-hour to off-peak settings). Switching to a communication-based or pulse-based system can completely resolve this issue.

LED light sources typically have a rated lifespan of over 50,000 hours, with some products rated for 100,000 hours. However, the actual service life of the signal unit often depends on the constant-current driver and the quality of the seals, rather than the LED chips themselves. The national standard GB 14887-2011 requires that, after one year of operation, the luminous intensity (brightness) along the reference axis must remain at no less than 80% of the specified value.

Troubleshooting steps:
Check if the supply voltage is stable.
Inspect the LED driver (flickering across the entire unit is usually a power supply issue).
Examine the LED module connectors and waterproof joints (partial outages are typically caused by poor contact or water ingress).
Verify the output phase of the controller.

Author introduction

About the author
Author

Hello Customers,

My name is Taylor Gong, I’m the product manager of ZGSM Tech. I have been in the LED lights industry for more than 13 years. Good at lighting design, street light system configuration, and bidding technology support. Feel free to contact us. I’m happy to provide you with the best service and products.

Email: [email protected] | WhatsApp: +8615068758483

  • Mail
  • Facebook
  • Twitter
  • YouTube
  • Instagram
  • LinkedIn
  • Pinterest


Post Tags: #LED Traffic Signals

Get In Touch

We're always excited about your message, so feel free to get in touch.
We will reply to you ASAP.

Category

LED Street Light
LED Flood Light
LED High Bay Light
LED Canopy Light
LED Garden Light
Solar Street Light
High Mast Light
LED Traffic Light
Lighting Accessories

Don't Want to Miss Anything?

Be the first to get updates and information about products and services.

  • Facebook
  • Twitter
  • Instagram
  • YouTube

© 2005 - 2026 · ZGSM Tech Warranty Terms | Privacy

Language Selection ES | FR | RU

  • Home
  • About us
    • Company Profile
    • Warranty term
    • Blogs
    • News
    • Privacy Policy
  • Products
    • LED Street Light

      High Mast Light

      Led Flood Light

      Solar Flood Light

      LED High Bay Light

      tunnel lights

      LED Tunnel Light

      LED Garden Light

      Led Bollard Light

      Solar Street Light

      red green yellow LED Traffic Light

      LED Traffic Light

      LED Canopy Light

      adapter

      Lighting Accessories

  • Solution
    • Smart Systems

      Smart Systems

      Simulation Design

      Smart Financing

      Smart Financing

  • Applications
  • Case Studies
  • Videos
  • Contact
Search